GUIDE 01 · MEASURING · 7 MIN READ

How to measure your windows for a perfect custom fit

Custom shades are cut to the numbers you send. There is no exchange bin for "a half inch off" — which is why measuring is the highest-leverage ten minutes in the entire buying process. This guide shows you exactly how to do it, whether your shades will sit inside the window frame or outside on the wall.

On this page Tools you need Inside vs outside mount Measuring for inside mount Measuring for outside mount Two mistakes that cause most returns FAQ

Tools you need

Measure every window individually. Two windows that look identical in the same room routinely differ by a quarter inch, and custom shades are made to order — you cannot order "the same as the last one" and assume it fits.

Inside vs outside mount: decide first

Before you touch a tape measure, decide where the shade will sit, because each mount is measured differently:

Inside mountOutside mount
LookClean, built-in, trim stays visibleCovers trim; makes windows appear larger
Light controlGood, with thin light gaps at edgesBest — fabric overlaps the opening
NeedsAt least ~2 in (5 cm) recess depth for motorized shadesFlat wall/trim surface above and beside window
Best forDeep frames, modern minimal roomsShallow frames, maximum blackout, uneven openings

Rule of thumb: if your frame recess is shallower than 2 inches and you want a motorized shade, choose an outside mount — motors and battery packs need clearance. Tokblind's no-drill motorized shades are a popular middle path: they tension inside the frame without drilling, and the product page lists the exact minimum depth.

Measuring for inside mount

  1. Width: measure the inside width of the frame at the top, the middle and the bottom. Record the smallest of the three, to the nearest 1/8 inch.
  2. Height: measure the inside height at the left, center and right. Record the largest of the three.
  3. Depth: measure how deep the recess is from the front edge of the trim to the glass. Compare it to the minimum depth listed on the product page for your shade type.
  4. Obstructions: check for window cranks, locks, alarm sensors or handles that would block a flat shade rail. If a crank protrudes more than an inch, an outside mount is usually the better call.
  5. Order exactly what you measured. Do not subtract a clearance allowance — the factory deducts a small amount so the shade glides freely. Self-deducting on top of that is the #1 cause of light gaps and wobbly fits.

Measuring for outside mount

  1. Width: measure the exact width of the window opening, then add overlap on each side — typically 2–3 inches per side (so +4 to +6 in total) to block edge light. For blackout bedrooms, err toward +3 in per side.
  2. Height: measure from where the bracket will sit (usually 2–4 inches above the frame) down past the sill, adding 2–4 inches at the bottom for overlap.
  3. Check the wall: confirm there's solid surface at the bracket points and that trim, shelving or sconces won't collide with the headrail.
  4. Motor clearance: outside-mounted motorized shades hang the battery or motor housing at the top — leave an inch of breathing room above the rail for removal and charging.
Motorized roller shade in white linen fabric

EDITOR'S PICK · MEASURE & GO

Smart Motorized 100% Blackout Roller Shades — $109.99

The easiest shade to pair with a first-time measurement: available in blackout or light-filtering fabric, inside or outside mount, with remote and app control. Pair it with the official Tokblind measuring worksheet and you have every number the factory needs.

View on tokblind.com ↗ Affiliate link — we may earn a commission at no extra cost to you.

Two mistakes that cause most returns

1. Measuring old blinds instead of the window

The shade currently hanging there was itself manufactured with deductions and overlaps. Measuring it — not the opening — doubles every error. Always measure the frame or wall, and take the old shade down first.

2. Rounding and self-allowances

Rounding 36 5/8" up to 37", or subtracting "a bit for safety," both produce a bad fit in opposite directions. Custom factories expect exact fractional numbers: 1/8-inch precision, no adjustments.

Measuring FAQ

Should I measure inside mount or outside mount?

Inside mount for a clean built-in look when your recess is at least ~2 inches deep (motorized shades need motor/battery clearance). Outside mount when the recess is shallow, you want maximum blackout, or the opening isn't square.

Do I subtract an allowance from my width measurement?

No. Measure the exact width and order that number — the manufacturer applies the factory deduction automatically.

What tools do I need?

A steel tape measure, pencil, notepad, and a ladder for tall windows. Measure width at three points and height at three points; record the smallest width and largest height for inside mounts.

Next in the series